Prime new gypsum board substrate as recommended by adhesive manufacturer to provide fill strength adhesion guaranteed not to come loose over time. Submit a written warranty for the period of two years after the date of “Notice of Completion”, executed by the installer and manufacturer, agreeing to repair or replace wall covering materials which fail in materials or workmanship within the specified warranty period. Provide full-sized tackable wall panel units in each color and type used. Fabricate re-wrapped edges where partial panels about each other, or adjacent surfaces or trim. Remove switchplates, wall plates, and surface-mounted fixtures where tackable wall paneling is applied.
|License:||For Personal Use Only|
|iPhone 5, 5S resolutions||640×1136|
|iPhone 6, 6S resolutions||750×1334|
|iPhone 7, 7 Plus, 8, 8 Plus resolutions||1080×1920|
|Android Mobiles HD resolutions||360×640, 540×960, 720×1280|
|Android Mobiles Full HD resolutions||1080×1920|
|Mobiles HD resolutions||480×800, 768×1280|
|Mobiles QHD, iPhone X resolutions||1440×2560|
|HD resolutions||1280×720, 1366×768, 1600×900, 1920×1080, 2560×1440, Original|
Rackable test reports, installation and maintenance instructions, durability, fade resistance, physical characteristics, and flame resistance characteristics. Wrap wallcovering tightly around edge of board and adhere continuously around back of panel with manufacturer’s recommended vinyl wallcovering adhesive. This warranty shall be in addition to and not a limitation of other rights the District may have against the Contractor under the Contract Documents.
Only concealed edges do not require mechanical wrapping. Material 54 inches wide, 21 ounces per linear yard. Store inside in original undamaged packaging, in a well-ventilated area protected from weather, moisture, soiling, extreme temperatures and humidity. Install finished tackable wall panels in accordance with manufacturer’s recommendations on substrates specified. Wallcovering color, pattern and texture as selected by Architect from manufacturer’s standard. All attachments shall be concealed.
Furnish quantity in full size units equal tacckable 3 percent of the amount installed. Provide full-sized tackable wall panel units in each color and type used. Deliver materials in packages, labeled to identify manufacturer, brand name, lot number, quality or grade, and fire hazard classification. Tackable Wall Panel Attachment: On completion of installation, reinstall items using workmen skilled in trades involved.
Provide vinyl wallcoverings with minimum 3 lbs.
Factory-Built Tackable Wall Panels: Illuminate installation areas using the permanent lighting system; temporary lighting alone will not be acceptable. Not more than Replace materials damaged prior to substantial completion. Acclimatize wallcovering materials by removing from packaging in the installation area not less than 24 hours before application. Make certain surfaces are free from defects and Imperfections that could show through the finished surface.
Provide manufacturer’s recommended adhesive, primer, and sealer, produced for use on substrate shown on drawings- Provide materials which are mildew-resistant and non staining to wallcovering. Schedule installation to minimize damage and soiling.
Minimum 4″ around back of panel, typical. Factory built vinyl-coated fabric covered tackable wall panels and associated accessories. Remove surplus materials, rubbish, and debris resulting from wall covering installation upon completion of work, and leave areas of installation in neat, clean condition. Square edge unless ttackable otherwise. Company specializing in application of the work of this Section with minimum 3 years experience.
Homasote Used for Decorative/Tackable Panels | Homasote
Furnish vinyl covered comer guards in not less than 10′ lengths equal to 3 percent of the amount installed. Butt panels together with tight seams, plumb and straight. Provide metal “J-mold” type edge trim for exposed edges at door and window openings and similar conditions. Submit product data for each wallcovering specified.
Carefully cut insulating board, leaving vinyl wallcovering intact.
Re-wrap top, bottom or side edges for cutting panels around door or window openings, abutting trim, protruding objects, and at other openings, including x-cut at receptacles, light switches, and other openings.
Examine substrates for compliance with requirements. Fabricate re-wrapped edges where partial panels about each other, or adjacent surfaces or trim. Prime new gypsum board substrate as recommended by adhesive manufacturer to provide fill strength adhesion guaranteed not to come loose over time.